Bolt Torque Calculator
Tightening torque and preload for metric bolts M3-M36, classes 4.6-12.9, by VDI 2230 or the nut-factor formula
About this Simulator
Calculate the tightening torque and the clamp force (preload) it produces for metric coarse-thread bolts from M3 to M36 in property classes 4.6 to 12.9. Use the VDI 2230 method, with thread and head friction set separately and preload at 90% of yield, or the quick nut-factor formula T = K·F·d. Example: an M12 8.8 bolt at μ = 0.12 needs 84 N·m for 43.1 kN of preload.
Physics & Formulas
Short form: the nut-factor formula
$$T = K \cdot F \cdot d$$
T is the tightening torque, F the preload (clamp force) you want, d the nominal diameter and K the nut factor, which lumps all friction together: about 0.2 for plain dry steel, about 0.15-0.18 lubricated. Shigley sets the preload at 75% of the proof load for reusable joints and 90% for permanent ones: F = 0.75 · As · Sp.
Long form: VDI 2230 (thread and head friction separately)
$$M_A = F_M\left(0.16\,P + 0.58\,d_2\,\mu_G + \frac{D_{Km}}{2}\,\mu_K\right)$$
The three terms are the torque that actually stretches the bolt (pitch P), thread friction (μG, pitch diameter d2) and friction under the head or nut (μK, mean bearing diameter DKm = (dw + dh)/2). VDI 2230 picks the preload so that tension plus the twisting from thread friction uses ν = 90% of the bolt's minimum yield strength Rp0.2:
$$F_M = \frac{A_s\,\nu\,R_{p0.2}}{\sqrt{1 + 3\left[\frac{3}{2}\frac{d_2}{d_0}\left(\frac{P}{\pi d_2} + 1.155\,\mu_G\right)\right]^2}}, \qquad A_s = \frac{\pi}{4} d_0^2,; d_0 = \frac{d_2 + d_3}{2}$$
with d2 = d − 0.6495P and d3 = d − 1.2269P (ISO 898-1). Rp0.2 min: 640 MPa for 8.8 up to M16 (660 above), 940 MPa for 10.9, 1100 MPa for 12.9.
Worked example: M12 8.8, μG = μK = 0.12
- P = 1.75 mm, d2 = 12 − 0.6495 × 1.75 = 10.863 mm, d3 = 9.853 mm, so As = 84.3 mm².
- Preload at 90% of yield (Rp0.2 = 640 MPa): FM = 43.1 kN.
- DKm = (16.63 + 13.5)/2 = 15.07 mm (ISO 4017 head on a 13.5 mm hole).
- MA = 43.11 kN × (0.16 × 1.75 + 0.58 × 10.863 × 0.12 + 7.533 × 0.12) = 83.6 N·m.
- Split: 14% stretches the bolt, 39% goes into thread friction, 47% into head friction. Equivalent nut factor K = 0.162.
- Cross-check: published VDI 2230 tables give 43.0 kN and 84 N·m for this case, and Bossard gives 41.9 kN and 93 N·m at μ = 0.14; this calculator gives 42.0 kN and 93 N·m there.
- The short form with K = 0.2 and 75% of proof load (580 MPa) gives F = 36.7 kN and T = 88 N·m: a similar torque for a lower clamp force, because K = 0.2 assumes more friction.
Metric bolt torque chart (VDI 2230 method, μ = 0.12, 90% yield)
| Size × pitch | Class 8.8 | Class 10.9 | Class 12.9 |
|---|---|---|---|
| M3 × 0.5 | 1.3 N·m (2.5 kN) | 1.9 N·m (3.7 kN) | 2.2 N·m (4.4 kN) |
| M4 × 0.7 | 3.0 N·m (4.4 kN) | 4.4 N·m (6.5 kN) | 5.1 N·m (7.6 kN) |
| M5 × 0.8 | 5.8 N·m (7.2 kN) | 8.6 N·m (10.6 kN) | 10 N·m (12.4 kN) |
| M6 × 1 | 10 N·m (10.2 kN) | 15 N·m (15.0 kN) | 17 N·m (17.5 kN) |
| M8 × 1.25 | 25 N·m (18.6 kN) | 36 N·m (27.4 kN) | 42 N·m (32.0 kN) |
| M10 × 1.5 | 48 N·m (29.6 kN) | 71 N·m (43.5 kN) | 83 N·m (50.9 kN) |
| M12 × 1.75 | 84 N·m (43.1 kN) | 123 N·m (63.3 kN) | 144 N·m (74.1 kN) |
| M14 × 2 | 134 N·m (59.1 kN) | 196 N·m (86.9 kN) | 230 N·m (101.7 kN) |
| M16 × 2 | 206 N·m (81.0 kN) | 302 N·m (118.9 kN) | 354 N·m (139.2 kN) |
| M20 × 2.5 | 416 N·m (130.5 kN) | 592 N·m (185.8 kN) | 693 N·m (217.5 kN) |
| M24 × 3 | 715 N·m (187.9 kN) | 1,018 N·m (267.6 kN) | 1,191 N·m (313.1 kN) |
| M30 × 3.5 | 1,428 N·m (300.0 kN) | 2,034 N·m (427.2 kN) | 2,381 N·m (499.9 kN) |
| M36 × 4 | 2,483 N·m (438.1 kN) | 3,537 N·m (624.0 kN) | 4,139 N·m (730.2 kN) |
Tightening torque with the preload it produces in brackets. Hex head bolts (ISO 4017) on medium clearance holes (ISO 273), coarse thread, steel on steel. These are upper values for the stated friction: if your μ is higher the same torque gives less clamp force, if lower (lubricated) the bolt can yield.
The catch: friction decides the clamp force
Only about 10-15% of the torque stretches the bolt. Apply the dry (μ = 0.14) M12 8.8 torque of 93 N·m to a lubricated bolt with μ = 0.10 and the preload jumps to about 56 kN, 33% more, past the 90%-of-yield design point. Torque wrenches also scatter: VDI 2230's tightening factor αA (about 1.4 to 2.5 for torque-controlled tightening, depending on how well friction is known) means the lowest preload can be half the highest, so design the joint for FM/αA.
Joint design, fastener selection and tolerance stacks are taught on real automotive parts in Skill-Lync's PG Program in Mechanical Design (CAD). For the parts being clamped, see the stiffness calculator (bolted joints are a stiffness problem: bolt and plates act as springs) and the section modulus calculator.
Formulas and chart checked 16 Nov 2026 by Skill-Lync against published VDI 2230 values. Strength values: ISO 898-1 minimums. Always follow the torque the part manufacturer specifies where one exists.
How to Use
- Pick the bolt size and property class (the number on the bolt head, e.g. 8.8 or 10.9)
- Choose the method: VDI 2230 for an engineering value, or the nut factor formula to match a K from a supplier or textbook
- For VDI 2230, set the thread and head friction (0.12 is typical for lightly oiled zinc-plated steel; 0.10 lubricated, 0.14-0.18 dry)
- For the nut factor method, set K (0.2 dry steel) and the preload as a percentage of the proof load (75% reusable, 90% permanent)
- Read the tightening torque in N·m and lbf·ft, the preload, and how much of the torque is lost to friction
- Use the lowest-preload card to check the joint still holds when the torque wrench scatters
Frequently Asked Questions
How do you calculate bolt tightening torque?
Use T = K·F·d: torque equals the nut factor K times the preload F times the bolt diameter d. For an M12 bolt with K = 0.2 and 36.7 kN preload, T = 0.2 × 36,700 N × 0.012 m = 88 N·m. VDI 2230 replaces K with separate thread and head friction terms for a more accurate value.
What is the tightening torque for an M12 8.8 bolt?
About 84 N·m for 43.1 kN preload at friction μ = 0.12, by VDI 2230 at 90% of yield. With μ = 0.14 (drier) it is about 93 N·m for 42.0 kN; lubricated at μ = 0.10, about 74 N·m for 44.2 kN. Use the manufacturer's value if one is given.
What nut factor K should I use?
K is about 0.2 for plain, dry steel bolts, 0.15-0.18 for lubricated or zinc-plated bolts, and as low as 0.10-0.12 with anti-seize or moly paste. VDI 2230 at μ = 0.12 works out to K ≈ 0.16 for M12. Measured K varies by ±25% or more, so a test on your actual parts beats any table.
Why does only a small part of the torque stretch the bolt?
Most of the torque is spent overcoming friction. For an M12 8.8 at μ = 0.12, about 14% of the torque stretches the bolt, 39% goes into thread friction and 47% into friction under the head or nut. That is why lubrication, plating and dirt change the clamp force so much.
Should bolts be tightened to 75% or 90% of proof load?
Shigley recommends a preload of 75% of the proof load for joints you will take apart and 90% for permanent joints. VDI 2230 instead tightens until the combined tension and thread torsion reach 90% of the minimum yield strength. Higher preload resists loosening and fatigue better, as long as the bolt is not yielded during tightening.
Does lubricating a bolt change the torque I should use?
Yes. Lower friction turns more of the same torque into stretch. Applying the dry M12 8.8 torque (93 N·m at μ = 0.14) to a bolt lubricated to μ = 0.10 raises the preload from 42.0 kN to about 56 kN, past the design limit. Always use a torque value for the lubrication you actually apply.