Section Modulus Calculator
Section modulus Z, moment of inertia I and bending stress for rectangle, hollow rectangle, circle, tube, I-beam and T-section
About this Simulator
Pick a cross-section, type or slide its dimensions, and get the elastic section modulus Z = I / y_max, the second moment of area I, the neutral axis position and the maximum bending stress for a given moment. Results are shown in mm, cm and m units. The shape is drawn to scale with its neutral axis and the linear bending stress distribution, so you can see why deep sections and tubes carry bending so well.
Physics & Formulas
Elastic section modulus
$$Z = \frac{I}{y_{max}} \qquad \sigma_{max} = \frac{M}{Z}$$
I is the second moment of area about the neutral axis (through the centroid) and ymax is the distance from that axis to the farthest fibre. Z is in mm³ (or m³); a bigger Z means a lower bending stress for the same moment.
Where it comes from (short derivation)
In pure bending, plane sections stay plane, so strain grows linearly with distance y from the neutral axis, and with Hooke's law so does stress: σ = E·y/R. The internal moment balances the applied one:
$$M = \int_A \sigma\, y\, dA = \frac{E}{R} \int_A y^2\, dA = \frac{E I}{R} \;\Rightarrow\; \sigma = \frac{M y}{I}$$
Stress is largest at y = ymax, so σmax = M·ymax/I = M/Z. Everything about the shape is packed into one number, Z.
Formulas for common sections
$$\text{Rectangle: } Z = \frac{b h^2}{6} \qquad \text{Solid circle: } Z = \frac{\pi d^3}{32}$$
$$\text{Hollow rectangle: } Z = \frac{B H^3 - b h^3}{6H} \qquad \text{Tube: } Z = \frac{\pi (D^4 - d^4)}{32 D}$$
$$\text{Symmetric I-beam: } I = \frac{b h^3 - (b - t_w)(h - 2t_f)^3}{12}, \quad Z = \frac{2I}{h}$$
T-sections are not symmetric: find the centroid first (ȳ = ΣA·y / ΣA), add each rectangle's own I plus A·d² (parallel-axis theorem), then use the larger distance from the centroid as ymax. The calculator does this for you and also shows Ztop and Zbottom.
Worked example 1: rectangular beam 50 × 100 mm
I = 50 × 100³ / 12 = 4,166,667 mm⁴, ymax = 50 mm, so Z = 83,333 mm³ (83.3 cm³), the same as bh²/6. Under a bending moment of 10 kN·m: σ = 10 × 10⁶ N·mm / 83,333 mm³ = 120 MPa. Mild steel (yield about 250 MPa) is fine; turn the same beam flat (h = 50 mm) and Z halves to 41,667 mm³, so stress doubles to 240 MPa.
Worked example 2: ISMB 200 I-beam
b = 100 mm, h = 200 mm, tf = 10.8 mm, tw = 5.7 mm. I = [100 × 200³ − 94.3 × 178.4³] / 12 = 2.205 × 10⁷ mm⁴ (2,205 cm⁴), Z = 2I/h = 220,482 mm³ (220.5 cm³). The IS 808 table lists 2,235.4 cm⁴ and 223.5 cm³: about 1.4% more, because rolled sections have root fillets between web and flange that this idealised shape leaves out. At M = 20 kN·m the stress is about 91 MPa.
Worked example 3: T-section
Flange 100 × 20 mm, web 20 × 80 mm (total depth 100 mm). Centroid: ȳ = (2000 × 10 + 1600 × 60) / 3600 = 32.2 mm below the top. I = 3.142 × 10⁶ mm⁴. Ztop = I / 32.2 = 97,517 mm³ but Zbottom = I / 67.8 = 46,361 mm³: the bottom of the web is the critical fibre, and the design value is the smaller Z.
Section modulus, I and bending stress are the first numbers you check before any FEA run. Skill-Lync's PG Program in CAE takes you from these hand calculations to HyperMesh, ANSYS and LS-DYNA models of real automotive parts, with mentor reviews.
How to Use
- Choose the cross-section: rectangle, hollow rectangle, circle, tube, I-beam or T-section
- Enter dimensions in mm with the sliders, or type an exact value in the box next to each slider
- Read Z (mm³, cm³, m³), I, y_max and area in the results below the drawing
- Set a bending moment in kN·m to get the maximum bending stress σ = M / Z in MPa
- For a T-section, use the smaller Z (shown first): it belongs to the fibre farthest from the centroid
- Press Animate load to see compression and tension flip as the moment reverses
Frequently Asked Questions
What is the formula for section modulus?
Section modulus is Z = I / y_max, where I is the second moment of area about the neutral axis and y_max is the distance from that axis to the farthest fibre. For a rectangle it simplifies to Z = bh²/6; for a solid circle Z = πd³/32. Maximum bending stress is then σ = M / Z.
What is the difference between section modulus and moment of inertia?
The second moment of area I (often called moment of inertia) measures how the area is spread around the neutral axis and controls deflection. Section modulus Z = I / y_max controls bending stress. Two sections with the same I can have different Z if one is deeper, so check stiffness with I and strength with Z.
How do I calculate the section modulus of an I-beam?
For a symmetric I-beam, I = [b·h³ − (b − t_w)(h − 2t_f)³] / 12 and Z = 2I / h. For ISMB 200 (b 100, h 200, t_f 10.8, t_w 5.7 mm) that gives about 220.5 cm³, against 223.5 cm³ in the steel table, which includes root fillets. Use the table value for design.
Why does a T-section have two section moduli?
A T-section's centroid is closer to the flange, so the top and bottom fibres are at different distances from the neutral axis. Z_top = I / y_top and Z_bottom = I / y_bottom. The smaller one, at the fibre farthest from the centroid (usually the web tip), gives the maximum stress and is the one to design with.
What is the difference between elastic and plastic section modulus?
The elastic section modulus Z = I / y_max gives the moment at which the outer fibre first yields. The plastic section modulus (Zp or S) assumes the whole section has yielded and is always larger: 1.5 times Z for a rectangle and about 1.14 times for a typical I-beam. Limit-state steel design (IS 800) uses Zp; this calculator gives the elastic Z.
Why is a hollow tube better in bending than a solid bar of the same weight?
Bending stress is carried mostly by material far from the neutral axis, because it enters I as y². A tube puts its material at the outside, so for the same area it has a much larger Z. A 60 mm tube with a 5 mm wall has about 89% of the section modulus of a solid 50 mm bar with only 44% of its area.
What units should I use for section modulus?
Section modulus has units of length cubed: mm³, cm³ or m³ (in.³ in US tables). Indian and European steel tables give it in cm³; 1 cm³ = 1,000 mm³. Keep units consistent: with M in N·mm and Z in mm³, σ = M / Z comes out directly in N/mm², which is MPa.