Stiffness Calculator
Stiffness k = F/δ for an axial bar, cantilever, simply supported beam, helical spring and shaft in torsion
About this Simulator
Calculate stiffness, the force per unit deflection, for the five cases engineers use most: an axial bar (k = AE/L), a cantilever with an end load (3EI/L³), a simply supported beam with a centre load (48EI/L³), a helical spring (Gd⁴/8D³n) and a solid shaft in torsion (GJ/L). Enter the dimensions and material, and get k in N/mm, N/m and kN/mm, the deflection or twist under your load, and the matching stress.
Physics & Formulas
Stiffness is load per unit deflection
$$k = \frac{F}{\delta}$$
k is in N/mm (or N/m). For twisting, torsional stiffness is torque per unit angle, kt = T/θ in N·m/rad. Every formula below comes from solving the deflection δ for a load F and dividing.
Axial bar
$$\sigma = E\varepsilon \Rightarrow \frac{F}{A} = E\frac{\delta}{L} \Rightarrow k = \frac{AE}{L}$$
Beams in bending
$$\text{Cantilever, end load: } \delta = \frac{F L^3}{3EI} \Rightarrow k = \frac{3EI}{L^3}$$
$$\text{Simply supported, centre load: } \delta = \frac{F L^3}{48EI} \Rightarrow k = \frac{48EI}{L^3}$$
Both deflections come from integrating EI·y'' = M(x) twice with the support conditions. Note the L³: double the span and the beam becomes 8 times softer. E is the material, I is the cross-section (get it from the section modulus calculator).
Helical spring
$$k = \frac{G d^4}{8 D^3 n}$$
The wire of a coil spring is really a long bar in torsion: wire length ≈ πDn, torque on the wire = F·D/2. Putting those into the torsion result θ = TL/(GJ) and taking δ = θ·D/2 gives the formula above. d is the wire diameter, D the mean coil diameter, n the number of active coils, G the shear modulus (about 79.3 GPa for spring steel).
Shaft in torsion
$$\theta = \frac{T L}{G J} \Rightarrow k_t = \frac{G J}{L}, \qquad J = \frac{\pi d^4}{32}$$
Worked examples (steel, E = 200 GPa, G = 79.3 GPa)
- Axial: 20 mm round bar, 1 m long. A = π × 20² / 4 = 314.2 mm². k = 314.2 × 200,000 / 1000 = 62,840 N/mm (62.8 kN/mm). A 10 kN pull stretches it 0.159 mm.
- Cantilever: ISMB 200 (I = 2,235.4 cm⁴ = 2.2354 × 10⁷ mm⁴), 2 m long. k = 3 × 200,000 × 2.2354 × 10⁷ / 2000³ = 1,677 N/mm. A 5 kN end load deflects it 2.98 mm.
- Simply supported: the same beam on a 2 m span, load at mid-span: k = 48EI/L³ = 26,825 N/mm, 16 times stiffer than the cantilever. 5 kN gives 0.19 mm.
- Spring: d = 5 mm, D = 40 mm, n = 10. k = 79,300 × 5⁴ / (8 × 40³ × 10) = 9.68 N/mm. At 100 N it compresses 10.3 mm; with the Wahl factor (C = 8, Kw = 1.184) the wire shear stress is 96.5 MPa.
- Torsion: 30 mm solid shaft, 1 m long. J = π × 30⁴ / 32 = 79,522 mm⁴. kt = 79,300 × 79,522 / 1000 = 6.31 × 10⁶ N·mm/rad = 6,306 N·m/rad (110 N·m per degree). 200 N·m twists it 1.82°.
Choosing each mode in the calculator loads its worked example. Hand-calculated stiffness is how you sanity-check an FEA model before you trust it. Skill-Lync's PG Program in CAE teaches stiffness, strength and crash analysis on real automotive parts in HyperMesh, ANSYS and LS-DYNA, with mentor reviews.
How to Use
- Pick what you are calculating: axial bar, cantilever, simply supported beam, coil spring or torsion shaft (each opens on its worked example)
- Enter the material modulus: E for bars and beams, G for springs and shafts (steel 200 / 79.3 GPa, aluminium 70 / 26 GPa)
- Enter the geometry with the sliders, or type an exact value in the box next to each slider
- For beams, enter I in cm⁴ (from a steel table or the section modulus calculator)
- Set the load (or torque) to see the deflection (or twist angle) and stress
- Press Animate load to see the part deform and spring back
Frequently Asked Questions
What is the formula for stiffness?
Stiffness is k = F / δ: the force needed per unit of deflection, in N/mm or N/m. For an axial bar k = AE/L, for a cantilever with an end load k = 3EI/L³, for a simply supported beam with a centre load k = 48EI/L³, for a coil spring k = Gd⁴/(8D³n), and for a shaft in torsion k = GJ/L.
How do I calculate the stiffness of a beam?
Find the deflection formula for your supports and load, then divide load by deflection. A cantilever with an end load has k = 3EI/L³; a simply supported beam with a centre load has k = 48EI/L³. E is Young's modulus, I the second moment of area of the section, L the span. Keep units consistent: N, mm, N/mm² and mm⁴ give k in N/mm.
What is the difference between stiffness and strength?
Stiffness is how much a part resists deflection (k = F/δ) and depends on E and geometry. Strength is the load it can carry before yielding or breaking and depends on yield or ultimate stress. Steel and aluminium alloys can have similar strength, but steel is about three times stiffer because its E is about 200 GPa against 70 GPa.
Why does a cantilever deflect so much more than a simply supported beam?
For the same span, section and load, a cantilever with an end load is 16 times less stiff than a simply supported beam loaded at mid-span (3EI/L³ against 48EI/L³). The cantilever has one support taking all the moment, and its maximum moment is F·L instead of F·L/4.
How does wire diameter change spring stiffness?
Spring stiffness grows with the fourth power of wire diameter and falls with the cube of coil diameter: k = Gd⁴/(8D³n). Going from 5 mm to 6 mm wire makes the spring about 2.07 times stiffer; doubling the coil diameter makes it 8 times softer; doubling the active coils halves it.
What are the units of stiffness?
Linear stiffness is force per length: N/mm, N/m or kN/mm (lbf/in in US units). 1 N/mm = 1,000 N/m. Torsional stiffness is torque per angle: N·m/rad or N·m per degree, where 1 N·m/rad = 0.01745 N·m/degree.
Is stiffness the same as Young's modulus?
No. Young's modulus E is a material property (about 200 GPa for steel, 70 GPa for aluminium). Stiffness k is a property of a part and combines E with geometry: a thin steel wire and a thick steel bar have the same E but very different k. That is why stiffness can be raised by changing the shape without changing the material.